Drag Mouse Over The Image To Zoom View.
Description
VURA FiSeal Pro
VURA FiSeal Pro is a ready to use nano imregnating sealer providing advance protection against water, oil and other stains. The product is absorbed by the capillary forces of the stone and can therefore penetrate into the stone structure.
CHARACTERISTICS
- Fluoropolymer based product
- Nano impregnating technology
- Breathable
- Resistance to UV radiation
- The color of the stone is normally not enhanced (preliminary test)
- Enhance adhesion strength
- Reduction of water and dirt absorption during periods of moisture
- Maintenance of breathing properties because there is no surface layer
Documents & Downloads
Usage Guide
Back and 4 sides of natural stone surfaces such as marble, granite, travertine, sandstone, limestone and absorbent material.
CLEANING
- Surface must be clean, dry and free from all waxes, layers/coatings
- It shall be taken into consideration that the stone contains no harmful salts (nitrates, sulphates, chlorides)
- The surface temperature should be between 10o to 35o C and sound
- Rinse well with water without fail after cleaning
- Before the stone is given its protective treatment, it must be totally dry. As a rule, this is the case after 1-2 days at the earliest
- Ensure that the area is well ventilated, and the surface is dry
PRE-TEST
Before starting the treatment, we recommend executing pre-tests, to examine the efficiency of the treatment, to evaluate the appearance of the treated surfaces (color enhancement) and to ascertain the material consumption as exactly as possible
Procedure of the treatment
- The best conditions for a treatment are an object- and surrounding temperature of 15o - 25°C and a protection from direct solar radiation and humidity exposure until the effectiveness of the protective effect
- In general, a single application is sufficient
- Apply the product with a brush, mop or an airless spraying equipment at low pressure (max. 1 bar over pressure) and a jet distance of 5-10 cm (condition: tubes and seals must be resistant to solvents)
- Approx. 20 minutes after application, respectively before the product has dried on the surface, any excess which has not been absorbed by the polished surface has to be completely removed with a suitable cloth so that no residue should remain on the polished surface
Description
VURA Oxi 7010
2 COMPONENTS, GEL FORM, EPOXY BASE THIXOTROPIC GLUE/PASTE
Vura Oxi 7010 is two components, epoxy base, gel form, solvent-free, thixotropic paste to fill and to firmly glue marble, stone, granite, quartz and ceramic. Suitable for outdoor and indoor application with low yellowing. it is soft and light with high gloss and brightness
CHARACTERISTICS
- Very neutral colour & easy to spread
- Low VOC content
- Very low tendency to yellow
- High creeping strength due to gel-like consistency
- Easy dosing and mixing by use
- Weather-resistant bonding
- Good dimensional stability of the bonding layer
- Low tendency to fatigue
- Good adhesion on slightly humid stones
- Very low shrinkage during the hardening process and therefore low tensions in the bonding layer
- Very good alkali-stability, thus the adhesive is very well suited to bond concrete
- Excellently suited for bonding gas-impermeable materials as it is a solvent-free product
Usage Guide
MIXING & APPLICATION
Vura Oxi 7010is mainly used in the stone-working industry for the weather-resistant bonding and glueing of natural stone (marble, granite), Artificial stone or building materials (terrazzo, concrete).
The two parts ie. glue and hardener must be kept on the original cans/tins. Thoroughly clean and slightly roughen surfaces to be bonded. Thoroughly mix 2 parts (A+B) (by weight) of component A with 1 part (by weight) of component B until a homogeneous mix is achieved.
Avoid the use of plastic made of PVC, do use only plastic resistant to corrosive liquids. Take out from the two containers A and B the required amounts indicated in weight, of the two components. Mix very well the 2 parts A+B and proceed to use. During the mixing use clean tools. Ensure that the marble to be treated with the resin is completely dry and clean.
By means of the application of high- quality raw materials it was possible to develop a system which hardly yellows. Because of its gel-like consistency the product has a high creeping strength on vertical surfaces. It is nevertheless possible to attain thin adhesive joints. Other materials can also be glued with Oxi 7010, e.g. paper, wood, glass and many other materials.
we suggest to verify the ratio every time. To clean the tools, we suggest to use aromatic and light solvent, The hardening process is accelerated by heat and delayed by cold.
