Drag Mouse Over The Image To Zoom View.
Description
VURA AquaRepWR
VURA AquaRep WR is a ready-to-use water-based water repellent for natural stones. It is a high quality and economical water repellence system for mineral and alkaline substrates. It does not changes the appearance of the substrate & gives a long lasting protection.
CHARACTERISTICS
- Easy to use – Brushable / Sprayable
- UV resistance
- Durable
- Water repellent
- Retains breathability of substrate (does not trap moisture)
- Resistance to alkalis
- Tack-free drying
- Invisible coating, does not change the color
- Cost effective
Documents & Downloads
WATER REPELLENT TREATMENT FOR
- Limestone & sandstones
- Clay, concrete & mortar
- Mangalore tiles
- Natural and artificial porous stones
- Bricks
PREPARATION OF A SAMPLE AREA
Surface temperature should be between 10o C to 35o C and surface should be clean and free of dirt, waxes, and protective coatings. Ensure that the area is well ventilated, and the surface is dry. Before starting we recommend preparing a sample area of 1-2m² to examine the efficiency of the impregnation.
Usage Guide
SURFACE PREPARATION
- Surface should be dry and free from all debris, dirt, oil, grease, wax and all other contamination which could prevent penetration
- Clean the saturated dirt of surface by thorough wire brushing, cleaning with compressed air followed by water washing
- Degrease oil & grease by using appropriate solvents
- Allow the surface to dry completely before the application
- Protect adjacent areas that are not to be treated. Since this is an impregnating product
- Seal the cracks using appropriate suitable products
APPLICATION
- Apply one liberal coat of VURA AquaRep WR by brushing / spraying evenly on the prepared surface
- Apply second coat wet on wet, to improve the penetration rate & performance
- Allow it to dry for 24 hrs.?
- After usage, close the tins well sealed
Description
VURA Oxi 7010
Vura Oxi 7010 is two components, epoxy base, gel form, solvent-free, thixotropic paste to fill and to firmly glue marble, stone, granite, quartz and ceramic. Suitable for outdoor and indoor application with low yellowing. it is soft and light with high gloss and brightness
CHARACTERISTICS
- Very neutral colour & easy to spread
- Low VOC content
- Very low tendency to yellow
- High creeping strength due to gel-like consistency
- Easy dosing and mixing by use
- Weather-resistant bonding
- Good dimensional stability of the bonding layer
- Low tendency to fatigue
- Good adhesion on slightly humid stones
- Very low shrinkage during the hardening process and therefore low tensions in the bonding layer
- Very good alkali-stability, thus the adhesive is very well suited to bond concrete
- Excellently suited for bonding gas-impermeable materials as it is a solvent-free product
Usage Guide
MIXING & APPLICATION
Vura Oxi 7010is mainly used in the stone-working industry for the weather-resistant bonding and glueing of natural stone (marble, granite), Artificial stone or building materials (terrazzo, concrete).
The two parts ie. glue and hardener must be kept on the original cans/tins. Thoroughly clean and slightly roughen surfaces to be bonded. Thoroughly mix 2 parts (A+B) (by weight) of component A with 1 part (by weight) of component B until a homogeneous mix is achieved.
Avoid the use of plastic made of PVC, do use only plastic resistant to corrosive liquids. Take out from the two containers A and B the required amounts indicated in weight, of the two components. Mix very well the 2 parts A+B and proceed to use. During the mixing use clean tools. Ensure that the marble to be treated with the resin is completely dry and clean.
By means of the application of high- quality raw materials it was possible to develop a system which hardly yellows. Because of its gel-like consistency the product has a high creeping strength on vertical surfaces. It is nevertheless possible to attain thin adhesive joints. Other materials can also be glued with Oxi 7010, e.g. paper, wood, glass and many other materials.
we suggest to verify the ratio every time. To clean the tools, we suggest to use aromatic and light solvent, The hardening process is accelerated by heat and delayed by cold.
