Drag Mouse Over The Image To Zoom View.
Description
VURA FasTone S1 (C2 T E S1)
Super Flexible
Deformable cementitious, polymer fibre modified adhesive with improved characteristic, resistance and extended open time. High performance adhesive for installing vitrified tiles, large scale tiles, thin tiles and slabs as well as natural stones
CHARACTERISTICS
- C2 TE S1 compliant with EN 12004 standard
- Type 4 T S1 as per IS 15477-2019
- With visible fibres for strength and flexibility balancing substrate deformations on critical surfaces like balconies, terraces, wet rooms, bathrooms, swimming pool and external facade etc
- For ceramic, vitrified tiles (semi and fully), glass mosaic and natural stone (non-sensitive)
- Suitable for large scale and heavy duty vitrified tiles
- Suitable for natural stones on internal as well as external application
- Suitable for tile on existing tile
- Suitable for vertical external stone/tile cladding
- On water proof and moisture proof layers
- For difficult substrate like heated floors and dry walls
- No vertical slip
- For inside and outside use
- Longer open time for safer application and adjustable
- Easy and excellent workability thanks to plastified consistency
- Application Up to 15mm
- Suitable for cement fibre board, gysum board (Internal application)
- Installation of floors subjected to heavy traffic
Documents & Downloads
Usage Guide
SUBSTRATE PREPARATION
Adhesive can be applied on even and compact substrates, free of any substances that reduce adherence (grease, bitumen, oil, paint, dust etc.). Concrete should be at least 1 month old. Cement screeds and plasters should be fully cured. Anhydrite (residual moisture below 0.5%), gypsum (residual moisture below 1%) substrates should be mechanically roughened and cleaned from dust. Dry wall Aerated concrete should be free from dust. Can be applied on existing tiles and should be roughened and cleaned before application. Substrates must not be wet. Any existing dirt, loose layers and paint coating shall be mechanically removed. Absorbent substrates shall be dampen and remove excess water before application.
APPLICATION
Pour VURA FasTone S1into a container with the precisely measured amount of clean water and stir with a drill and mixer until a homogeneous mass without lumps is obtained. Leave for 5 min. and then stir the mixture again. Apply the mortar with a suitable notched trowel. Use the proper sized notch trowel to ensure full bedding in the tile. The depth of trowel's notching is depends on the size of tile / stone. The back buttering method shall be used for larger tiles / stones and for outdoor applications (ie. additionally a thin layer of the mortar should be spread on the tile/stone's back side, contact area > 90%). Place the tiles/stones only during the open time of the adhesive. Lay the mortar and press while the mortar is still sticky. Fresh excess mortar can be removed with water, hardened material can only be removed mechanically. Grouting can be performed no earlier than after 24 hours using VURA tile grouts. Floors are set to light traffic after approx. 24 hrs. Expansion joints, joints at the corners of walls and floor and around sanitary equipment shall be filled with sealants or shall be treated with appropriate treatment
Description
VURA FasTone S1 (C2 T E S1)
Super Flexible
Deformable cementitious, polymer fibre modified adhesive with improved characteristic, resistance and extended open time. High performance adhesive for installing vitrified tiles, large scale tiles, thin tiles and slabs as well as natural stones.
CHARACTERISTICS
- C2 TE S1 compliant with EN 12004 standard
- Type 4 T S1 as per IS 15477-2019
- With visible fibres for strength and flexibility balancing substrate deformations on critical surfaces like balconies, terraces, wet rooms, bathrooms, swimming pool and external facade etc
- For ceramic, vitrified tiles (semi and fully), glass mosaic and natural stone (non-sensitive)
- Suitable for large scale and heavy duty vitrified tiles
- Suitable for natural stones on internal as well as external application
- Suitable for tile on existing tile
- Suitable for vertical external stone/tile cladding
- On water proof and moisture proof layers
- For difficult substrate like heated floors and dry walls
- No vertical slip
- For inside and outside use
- Longer open time for safer application and adjustable
- Easy and excellent workability thanks to plastified consistency
- Application Up to 15mm
- Suitable for cement fibre board, gysum board (Internal application)
- Installation of floors subjected to heavy traffic
Usage Guide
SUBSTRATE PREPARATION
Adhesive can be applied on even and compact substrates, free of any substances that reduce adherence (grease, bitumen, oil, paint, dust etc.). Concrete should be at least 1 month old. Cement screeds and plasters should be fully cured. Anhydrite (residual moisture below 0.5%), gypsum (residual moisture below 1%) substrates should be mechanically roughened and cleaned from dust. Dry wall Aerated concrete should be free from dust. Can be applied on existing tiles and should be roughened and cleaned before application. Substrates must not be wet. Any existing dirt, loose layers and paint coating shall be mechanically removed. Absorbent substrates shall be dampen and remove excess water before application.
APPLICATION
Pour VURA FasTone S1into a container with the precisely measured amount of clean water and stir with a drill and mixer until a homogeneous mass without lumps is obtained. Leave for 5 min. and then stir the mixture again. Apply the mortar with a suitable notched trowel. Use the proper sized notch trowel to ensure full bedding in the tile. The depth of trowel's notching is depends on the size of tile / stone. The back buttering method shall be used for larger tiles / stones and for outdoor applications (ie. additionally a thin layer of the mortar should be spread on the tile/stone's back side, contact area > 90%). Place the tiles/stones only during the open time of the adhesive. Lay the mortar and press while the mortar is still sticky. Fresh excess mortar can be removed with water, hardened material can only be removed mechanically. Grouting can be performed no earlier than after 24 hours using VURA tile grouts. Floors are set to light traffic after approx. 24 hrs. Expansion joints, joints at the corners of walls and floor and around sanitary equipment shall be filled with sealants or shall be treated with appropriate treatment
