Drag Mouse Over The Image To Zoom View.
Description
VURA PowerSeal Pro
VURA PowerSeal Pro is a fluoropolymer based ready to use product, which is weather resistant, UV resistant, premium nano impregnating sealer providing ultimate protection against water, oil and other stains. PowerSeal Pro is absorbed by the stone due to the capillary forces, however, without closing the pores, therefore the product is very effective and durable.
CHARACTERISTICS
- Fluoropolymer based chemistry
- Nano impregnating technology
- Oleophobic and Hydrophobic
- Fast curing and development of protective effect
- Low colour enhancement
- Very good oil- and grease stain repellent effect
- Very good reduction of water- and dirt absorption when exposed to moisture and high humidity
- Fast liberation of humidity during dry periods due to high vapor permeability
- Surfaces able to breath because there is no surface layer
- Non yellowing
- Maximum protection against stains
- Resistance to UV radiation
- No release of methanol during cure/drying
- Preserve natural look
Documents & Downloads
Usage Guide
- Natural stones - Marble - Granite - Travertine - Sandstone - LimestoneCLEANING
- The surface must be clean, completely dry and free from all layers and coatings
- In outdoor areas it must be taken care that the stone does not contain any harmful salts since these reduce the absorptive capacity of the stone
- Surface Temperature should be between 10 to 35 deg C
- Surface should be sound and free from all dirt
- In any case, after cleaning rinse well with water. Before the stone is given its protective treatment, it must be totally dry. As a rule, this is the case after 1-2 days at the earliest
- Ensure that the area is well ventilated
PREPARATION OF A SAMPLE AREA
Before starting we recommend preparing a sample area of 1-2 m² to examine the efficiency of the impregnation, to evaluate the appearance of the treated object and to ascertain the material consumption as exactly as possible
IMPREGNATION PROCEDURE
- Shake well before use. The best condition for impregnating is a temperature of 5o-35o C and protection from humidity for approx. 2-3 hours
- The stone must not be warmed up by an underfloor heating or direct sunlight
- In general, one to two coat wet-in-wet are sufficient
- Apply the product with a brush or a mop. Spread liberally over the substrate
- Allow sealer to penetrate the surface for 15-30 minutes
- Any excess material which has not been absorbed by the stone has to be completely removed with a suitable cloth. Polished surfaces must additionally be polished again until any blooming on the surface is removed
- If the desired effect is not achieved or if the impregnation has been applied unevenly, it is possible to apply the impregnation once again
- The water-repellent effect develops after a few minutes, full protection after 24-72 hours
- A full cure is achieved after 24-72 hrs. Foot traffic is allowed after 6-8 hrs
- Sufficient ventilation (approx. 2-3 days) is necessary when using the product in food areas
- Tools can be cleaned with thinner or mineral spirit
Description
VURA Oxi 7010
2 COMPONENTS, GEL FORM, EPOXY BASE THIXOTROPIC GLUE/PASTE
Vura Oxi 7010 is two components, epoxy base, gel form, solvent-free, thixotropic paste to fill and to firmly glue marble, stone, granite, quartz and ceramic. Suitable for outdoor and indoor application with low yellowing. it is soft and light with high gloss and brightness
CHARACTERISTICS
- Very neutral colour & easy to spread
- Low VOC content
- Very low tendency to yellow
- High creeping strength due to gel-like consistency
- Easy dosing and mixing by use
- Weather-resistant bonding
- Good dimensional stability of the bonding layer
- Low tendency to fatigue
- Good adhesion on slightly humid stones
- Very low shrinkage during the hardening process and therefore low tensions in the bonding layer
- Very good alkali-stability, thus the adhesive is very well suited to bond concrete
- Excellently suited for bonding gas-impermeable materials as it is a solvent-free product
Usage Guide
MIXING & APPLICATION
Vura Oxi 7010is mainly used in the stone-working industry for the weather-resistant bonding and glueing of natural stone (marble, granite), Artificial stone or building materials (terrazzo, concrete).
The two parts ie. glue and hardener must be kept on the original cans/tins. Thoroughly clean and slightly roughen surfaces to be bonded. Thoroughly mix 2 parts (A+B) (by weight) of component A with 1 part (by weight) of component B until a homogeneous mix is achieved.
Avoid the use of plastic made of PVC, do use only plastic resistant to corrosive liquids. Take out from the two containers A and B the required amounts indicated in weight, of the two components. Mix very well the 2 parts A+B and proceed to use. During the mixing use clean tools. Ensure that the marble to be treated with the resin is completely dry and clean.
By means of the application of high- quality raw materials it was possible to develop a system which hardly yellows. Because of its gel-like consistency the product has a high creeping strength on vertical surfaces. It is nevertheless possible to attain thin adhesive joints. Other materials can also be glued with Oxi 7010, e.g. paper, wood, glass and many other materials.
we suggest to verify the ratio every time. To clean the tools, we suggest to use aromatic and light solvent, The hardening process is accelerated by heat and delayed by cold.
