Drag Mouse Over The Image To Zoom View.
Description
VURA FiSeal +
WATER BASE BACK COAT PENETRATING SEALER TO RESIST
STAINS
VURA FiSeal + is chemically reactive penetrating sealer that creates cross linked internal membrane that fuses within the substrate to prevents contaminants from rising up to the surface without altering the adhesion properties of the adhesive. It allows moisture vapour transmission and does not adversely affect bonding of stone to substrate. Protects the material and improves its cohesion thanks to its consolidating action. It is penetrating sealer to provide protection from water and stain absorption for most natural stones ie. Marble, slate, granite, limestone, sand stone, travertine etc.
CHARACTERISTICS
- Water-repellent and consolidating action
- Does not alter the material's appearance
- A VOC-free product with a low environmental impact
- UV resistant
- Breathable
- Blocks contaminants from rising to the material surface
- Easy to use
- Protection against moisture, water and most stains
- Does not substantially alter the adhesion characteristics of the adhesive
- For interior and exterior applications
Documents & Downloads
WHERE TO USE
Back and 4 sides of Natural stone surfaces such as Granite, Marble, Limestone, Slate, Travertine, Terracotta and Absorbent Material.
APPLICATION
Shake before using. Thoroughly clean the back of tile or slab, removing any dust and residues. Apply the product evenly with a paint pad, sponge, brush or roller on the back and on the edges of the material. Allow 3-5 minutes for sealer to soak into surface. Remove excess material / non absorbed material with clean towel or absorbent paper. Porous surfaces may require further applications. After 3 hours, conduct a test to see the surface completely sealed by applying drops of water on the surface. In case of any absorption, apply an additional coat. Leave the product to dry from 12 hours (at +23° C and 50% R.H.) before fixing the stones with suitable adhesive, Please consult with Vura representative for adhesive recommendations.
PRECAUTIONS
- Review cautionary information prior to use
- Avoid skin contact by wearing specific gloves
- Begin with a clean, dry surface that is free of waxes and coatings
- Always test in a small inconspicuous area with a 12-hour cure time to determine ease of application and desired results. Water droplets can be applied after a 3-hours cure to determine water repellency
- Surface must be dry and free on contaminants, including previously applied sealers, dirt, lime & hard water deposits, rust & other heavy dirt
- Sealer may be applied to damp surfaces 1 hour after standing water is removed in good environment conditions
- Surface temperature should be between +10° C and +50° C
- Ensure that the area is well-ventilated during application and until the surface is dry
Drag Mouse Over The Image To Zoom View.
Description
VURA FiSeal +
WATER BASE BACK COAT PENETRATING SEALER TO RESIST
STAINS
VURA FiSeal + is chemically reactive penetrating sealer that creates cross linked internal membrane that fuses within the substrate to prevents contaminants from rising up to the surface without altering the adhesion properties of the adhesive. It allows moisture vapour transmission and does not adversely affect bonding of stone to substrate. Protects the material and improves its cohesion thanks to its consolidating action. It is penetrating sealer to provide protection from water and stain absorption for most natural stones ie. Marble, slate, granite, limestone, sand stone, travertine etc.
CHARACTERISTICS
- Water-repellent and consolidating action
- Does not alter the material's appearance
- A VOC-free product with a low environmental impact
- UV resistant
- Breathable
- Blocks contaminants from rising to the material surface
- Easy to use
- Protection against moisture, water and most stains
- Does not substantially alter the adhesion characteristics of the adhesive
- For interior and exterior applications
WHERE TO USE
Back and 4 sides of Natural stone surfaces such as Granite, Marble, Limestone, Slate, Travertine, Terracotta and Absorbent Material.
APPLICATION
Shake before using. Thoroughly clean the back of tile or slab, removing any dust and residues. Apply the product evenly with a paint pad, sponge, brush or roller on the back and on the edges of the material. Allow 3-5 minutes for sealer to soak into surface. Remove excess material / non absorbed material with clean towel or absorbent paper. Porous surfaces may require further applications. After 3 hours, conduct a test to see the surface completely sealed by applying drops of water on the surface. In case of any absorption, apply an additional coat. Leave the product to dry from 12 hours (at +23° C and 50% R.H.) before fixing the stones with suitable adhesive, Please consult with Vura representative for adhesive recommendations.
PRECAUTIONS
- Review cautionary information prior to use
- Avoid skin contact by wearing specific gloves
- Begin with a clean, dry surface that is free of waxes and coatings
- Always test in a small inconspicuous area with a 12-hour cure time to determine ease of application and desired results. Water droplets can be applied after a 3-hours cure to determine water repellency
- Surface must be dry and free on contaminants, including previously applied sealers, dirt, lime & hard water deposits, rust & other heavy dirt
- Sealer may be applied to damp surfaces 1 hour after standing water is removed in good environment conditions
- Surface temperature should be between +10° C and +50° C
- Ensure that the area is well-ventilated during application and until the surface is dry
