Drag Mouse Over The Image To Zoom View.
Description
VURA Dur
VURA Dur is a ready to use, dry shake, non metallic preblended floor hardener for concrete based on natural mineral aggregates and special additives. VURA Dur provides a hard wearing and abrasion resistant topping for monolithic floors. It forms a smooth, dense, anti skid, long lasting and maintenance free floor when sprinkled and trowelled into fresh wet concrete floors.
CHARACTERISTICS
- Single component / Ready to use
- Not metallic & Rust free
- High wear resistance
- High abrasion resistant
- High impact resistance
- Cost effective surface hardener
- Makes floor dust proof
- Easy to clean
- Increase resistance to oils and grease
- Quality assured - factory blending
Documents & Downloads
Usage Guide
APPLICATION
VURA Durmay only be used by experienced professionals.
Application time for dryshake products is influenced by every variable which affects the placing of concrete, and can therefore vary substantially, depending on the prevailing conditions.
Dependent on the conditions, remove the surface bleed water or allow it to evaporate. Sprinkle VURA Dur onto the screed concrete evenly in 2 stages, In first stage, two third ie. 60-70% of the dry mix should be sprinkled evenly by hand or scoop horizontally and it is to be floated by wooden float or mechanically floating. In second stage, therefater imediately the remaining 30- 40% dry mix should be sprinkled. Care must be taken to apply the product without creating ripples etc. in the concrete surface. The first application must be worked into the slab immediately followed by application of the second stage quantity of VURA Dur.
While floating, surface should not be over worked.
Final finishing, closing pores and removing undulations can be achieved either by hand or powered trowel.
For mechanical application with automatic spreader and laser screed, the spreading can start almost immediately after the concrete has been levelled to allow for the hydration of the dryshake. Compaction with the trowel can start as soon as the weight of the power trowels is supported by the concrete.
For manual application, the dry shake must be spread once the concrete becomes firm enough to take foot traffic.
Description
VURA Dur
VURA Dur is a ready to use, dry shake, non metallic preblended floor hardener for concrete based on natural mineral aggregates and special additives. VURA Dur provides a hard wearing and abrasion resistant topping for monolithic floors. It forms a smooth, dense, anti skid, long lasting and maintenance free floor when sprinkled and trowelled into fresh wet concrete floors.
CHARACTERISTICS
- Single component / Ready to use
- Not metallic & Rust free
- High wear resistance
- High abrasion resistant
- High impact resistance
- Cost effective surface hardener
- Makes floor dust proof
- Easy to clean
- Increase resistance to oils and grease
- Quality assured - factory blending
Usage Guide
APPLICATIONVURA Durmay only be used by experienced professionals.
Application time for dryshake products is influenced by every variable which affects the placing of concrete, and can therefore vary substantially, depending on the prevailing conditions.
Dependent on the conditions, remove the surface bleed water or allow it to evaporate. Sprinkle VURA Dur onto the screed concrete evenly in 2 stages, In first stage, two third ie. 60-70% of the dry mix should be sprinkled evenly by hand or scoop horizontally and it is to be floated by wooden float or mechanically floating. In second stage, therefater imediately the remaining 30- 40% dry mix should be sprinkled. Care must be taken to apply the product without creating ripples etc. in the concrete surface. The first application must be worked into the slab immediately followed by application of the second stage quantity of VURA Dur.
While floating, surface should not be over worked.
Final finishing, closing pores and removing undulations can be achieved either by hand or powered trowel.
For mechanical application with automatic spreader and laser screed, the spreading can start almost immediately after the concrete has been levelled to allow for the hydration of the dryshake. Compaction with the trowel can start as soon as the weight of the power trowels is supported by the concrete.
For manual application, the dry shake must be spread once the concrete becomes firm enough to take foot traffic.
